FREE SHIPPING AUSTRALIA WIDE
Free shipping on all retail orders
AUSTRALIAN OWNED & OPERATED
Licenced WaterMark Supplier
Twin Alternating 9” x 35” Water Softener with 100LT Brine Tank 15-25 L/PM (GT41-32-TA9)
- Twin 9” x 35” Water Softener with 100L Brine Tank - Dual Brine Well
- 15L/PM (Continuous) – 25L/PM (Peak) Flow rate
- 25 Lt each of Food Grade Softening Resin
- Genuine Autotrol 255 Head with 764T Micro Processor Fully Programable with Interconnect
- Pre-Loaded Vessel for easy installation
- Built in Raw Water Bypass (No Hardwater Bypass option is available)
- Uninterrupted and continuous soft water flow
Twin Alternating 9” x 35” Water Softener with 100LT Dual Brine Well Single Tank
Have you got Hard Water??? Installing a Filter Systems Australia water softener will remove limescale and eliminate those hard water stains leaving you with soft water saving you time and money.
Twin alternating softeners are ideal for situations where uninterrupted flow of soft water is a must. One resin tank is always in service, while the other tank is in standby. When the meter determines that the resin is near its capacity, it will switch the tank in standby to be in service, and the tank containing the exhausted resin will begin regeneration and wait in standby until the other tank is ready for regeneration.
What is hard water? Hardness is a measurement of calcium and magnesium in water and this can cause staining, calcification and may damage appliances, hot water systems, pipes and fittings over time if not properly addressed. Removing hardness from the water will greatly improve the quality of the water and its effects include lower surface tension, better effects from soaps and detergents, healthier hair and skin, longer lasting appliances (such as kettles, dishwasher, hot water cylinder etc.) and fixtures, less scale build up in showers.
Brief Technical Explanation of how a softener works:
Softeners are full of cation exchange resin. The resin beads have sodium ions attached to them. As the hard water passes through the resin bed, the calcium and magnesium ions swap places with the sodium ions.
The calcium and magnesium ions are left attached to the beads, while the water leaving the water softener contains more sodium ions. The hard water is softened because it no longer contains calcium or magnesium ions.
Once the resin beads in the softener become saturated with calcium and magnesium ions, they must be regenerated by adding sodium chloride (Water Softening salt). The sodium ions replace the calcium and magnesium ions on the beads. Sodium chloride is cheap and widely available, making this a convenient and cost-effective system.
Please note: these systems have been based on treated mains water, if you wish to treat bore water please contact us before purchasing to ensure this system is suitable for your needs.
Please note: These systems exlcude softening salt, we advise you source softening salt locally
Features
- Twin 9” x 35” Water Softener with 100L Brine Tank - Dual Brine Well
- 15L/PM (Continuous) – 25L/PM (Peak) Flow rate
- 25 Lt each of Food Grade Softening Resin
- Genuine Autotrol 255 Head with 764T Micro Processor Fully Programable with Interconnect
- Pre-Loaded Vessel for easy installation
- Built in Raw Water Bypass (No Hardwater Bypass option is available)
- Uninterrupted and continuous soft water flow
System Performance
Please note: the performance is based on 150ppm of Hardness, these values can change please contact us directly with a copy of your water analysis to ensure this softener can be sized correctly
Example 1:
| Hardness Setting | 150ppm |
| Salt Setting | 110gr |
| Salt Usage | 2.8 kg per regeneration |
| Capacity Removal | 1.4kg |
| Calendar Override | Set to Zero |
| Water Treated | 9,300L per vessel (before regeneration is required) |
| Service Flow rate | 15 L/PM Continuous |
| Peak Flow rate | 25 L/PM |
| Backwash Flow rate | 6.4 L/PM |
Example 2:
| Hardness Setting | 250ppm |
| Salt Setting | 110gr |
| Salt Usage | 2.8 kg per regeneration |
| Capacity Removal | 1.4kg |
| Calendar Override | Set to Zero |
| Water Treated | 5,600L per vessel (before regeneration is required) |
| Service Flow rate | 15 L/PM Continuous |
| Peak Flow rate | 25 L/PM |
| Backwash Flow rate | 6.4 L/PM |
System Dimensions
Vessel Inc Head x 2
950 mm Height x 350mm Width Approx.
Brine Tank
460 mm x 875 mm
Specifications:
Inlet/Outlet Manifold: 3/4” or 1” BSP options available
Bypass Manifold: ¾” or 1” BSP (recommended for easier future maintenance)
Drain : ½” Male
Brine Draw: 3/8” Tube
Return Policy
Due to the nature of the products we sell, a strict return policy is in place. We work with food grade certified materials that must be un-opened and un-used as to be able to be re-sold.
You may receive a refund or credit of equal amount, less the restocking fee if applicable and any other deductions that are relevant.
- Wrongly purchased items may be returned for a merchandise credit, this applies for but not limited to: Wrong size, wrong system etc.
- 30 Day return Policy: Returns will not be accepted without prior approval or after 30 days of invoice date.
- All returns will incur a 17.5% restocking fee or cost to send the item to you whichever greater. FSA may use discretion to determine the restocking fee.
- Any damages (minor, that can be repaired) will incur a fee which will be deducted from the total refund which will be equal to the cost of the replacement
parts (List Price) and labour charge (if applicable) to repair the system(s). This will be separate to the restocking fee. - Any damage considered to be major and not feasible for repair may be refused and the return request will be void. The customer will be responsible for the return freight or disposal of the damaged unit.
- Return shipping is to be paid by the buyer to the address provided. It is recommended that the customer applies transit warranty to the return freight in case of damage.
- Any damages to the system that were not reported to FSA within 48 business hours of receipted delivery are not covered under our transit warranty.
- Should the item appear faulty or doesn’t work how described, the unit/item must be returned for testing (if requested), the return postage paid by the buyer. If the unit/item is deemed to be faulty, compensation will be provided for the postage cost (Proof of cost required). If the unit/item is deemed to be in working order and as described, the buyer will responsible for return postage.
If you have any questions about our return policy, please contact us before purchase. This will also help to ensure you purchase the correct product that suits your requirements.