6 Stage Hydrogen Rich Reverse Osmosis Water Filter 1 Year Replacements GT1-11SH
Replacement Pack Suited to the NEW 6 Stage Portable Hydrogen Rich Reverse Omsosis Water Filter System
- Stage 1: Inline GAC Carbon Pre-Filter 1 Micron
- Stage 3: T300 Hydrogen-Rich Water Filter Cartridge 1 Micron
- Stage 5: Puretron Inline Carbon Filter 1 Micron
Changing your filters:
Inline water filter cartridges are very simple to install and dismantle. As the name suggests, the water flow is inline which means that either end of the cartridge contains a fitting to accommodate tubing.
When changing filters on the 6 stage Shuttle, we recommend taking a photo of the system from various angles, then one by one, changing the cartridges. This will help you remember the orientation of the filters and the flow direction and may save you time trying to put the filter back together from scratch.
- Using Push-Fit Connections: These connections are very easy to use however if you have not used them before, may be a little tricky at first. To remove the tubing, depress the floating collet, then pull on the tubing and it should release. When re-installing, you need to firmly push the tubing into the opening until you feel a “click” which signifies that the tubing has pushed through the internal O-ring and is seated correctly. If leaking occurs, it may be due to roughly cut tubing OR the tubing is not pushed in far enough. See images to the right for visual instruction on push fit connectors.
- Installing Fittings: All fittings, excluding the membrane housing fittings (1/8"), come with an o-ring fitted to seal the connection. For quality assurance and extra security, when the fittings are installed, we apply 6-8 rounds of standard white plumbing tape to the fittings. It is recommended that you also apply thread tape when re-installing fittings to help prevent leaks over time. Ensure that you remove all thread tape (as best you can using a stanly knife) without damaging the thread of the fitting, then apply approx 6 rounds of thread tape. If you experience any leaks or cross threading, the fitting may require replacement and can be purchased from our store. You will require a shifter to install these fittings.
- System Restart: When the new filters are installed, you will then need to flush the system again. Much the same as when you first use the system. Disconnect the tubing from the screw cap end of the membrane and flush the water through the pre-filter (stage 1) for approx 1-2 minutes, shaking the filter frequently to loosen any carbon fines. When this has been completed, reconnect the system and run for about 15-20 minutes to flush out the remaining filters. HINT: If you can, plug each filter directly into the inlet line and flush it straight off the kitchen tap pressure. This will greatly shorten the flushing times.
T300 Hydrogen Rich Water Filter (GT6-32)
Made from pure Magnesium
Certification 2008 FDA No. 163-28666-872
Service Life: 12 Months or 4,000L
Max Flow: 2.8L/Min
Max Pressure: 125 PSI
Max Temp: 55°C
Made In Taiwan
Inline Carbon Taste & Odour Filter (GT6-1)
NSF/ANSI 42 Certification
Service Life Stage 1: 6 Months or 2,000L
Service Life Stage 5: 12 Months or 4,000L
Max Flow: 2.8L/Min
Max Pressure: 125 PSI
Rating: 1 Micron Nominal
Due to the nature of the products we sell, a strict return policy is in place. We work with food grade certified materials that must be un-opened and un-used as to be able to be re-sold.
You will receive a credit of equal amount, less the postage cost to send it to you.
- Wrongly purchased items may be returned for a merchandise credit, this applies for but not limited to: Wrong size, wrong system etc.
- 30 Day return Policy: We will accept returns up to 30 days after the initial purchase, all orders should be checked immediately for damage/fault upon arrival to aid us with the return process.
- Return shipping is to be paid by the buyer to the address provided
- Should the item appear faulty or doesn’t work how described, the unit/item must be returned for testing (if requested), the return postage paid by the buyer. If the unit/item is deemed to be faulty, compensation will be provided for the postage cost. If the unit/item is deemed to be in working order and as described, the buyer will need to pay for return postage.
If you have any questions about our return policy, please contact us before purchase. This will also help to ensure you purchase the correct product that suits your requirements.