1. See Detail

Faucet Tap Water Filter Coconut Carbon Faucet Mount Water Purifier Kitchen GT39-18

SKU
GT39-18
In stock
Special Price A$55.00 was A$95.00
or 4 interest-free payments of $13.75
Learn more

Faucet Mount Water Filter

Compact Faucet Mount Water Purifier. Filter Municipal (Chlorinated) Town Water Straight from the tap.

Supplied with adaptors and fittings to connect to most Kitchen taps.
Twin Outlet allowing a filter bypass when filtered water is not required, change between unfiltered and filtered water at the push of a button.

Simple maintenance with quick change housings - no plumber required - DIY Friendly Product.

Catalytic Carbon Block Technology for high absorption of Chlorine and other VOC's in water.

Whats in the Box

  • Carbon Block
  • Filter Cartridge Cover
  • Filter Base
  • Selector
  • Stainless Steel Mesh
  • Silicone Washer
  • External/Internal Thread Adaptors (19mm - 23.5mm)
  • 1/2" or 3/4" External Faucet Adaptor with Screw Clamp
  • Tool for Adaptor Installation
  • Washers for External/Internal Adaptors
  • Instruction manual
  • Thread Tape

Before Purchase / Installation

  • Do not use with microbiologically unsafe water or of water of unknown quality without adequate disinfection before or after the system.
  • Operation Pressure must not exceed 400 kPa. If pressure exceeds this, you must install a pressure limiting device before the tap.
  • This device fits faucets ranging from 19mm to 23.5mm OD. Adaptors for both male and female are supplied. Please ensure your tap is suitable before purchase.
  • Water quality may affect the life of the filter cartridge, this can become an indication of when you require a cartridge change if the filter blocks before the recommended replacement time.
  • Prior to usage, it is recommended to run the water briefly in ‘Pure Mode’ to ensure the filter has been flushed and filter correctly.
  • The filter will require a 1-minute flush if it has not been used for periods over 48 hours.
  • The maximum temperature of this water filter is 38°C. Not for use with Hot Water. Using Hot water on this filter may cause damage or failure and void warranty.

Installation

For diagrams of installation, please refer to manufacturer’s supplied manual.
Remove your original aerator and its washer. Use a spanner or multi grip tool if difficult to remove.
Identify the size and type of faucet thread by using a ruler or calipers and select the correct adaptor. 

  1. Take off the mounting nut. (I)
  2. Attach the correct adaptor (H) with the washer to the faucet with the mounting nut on (I)
  3. Connect the Selector base and silicone washer (G + D,E) and tighten using the mounting nut (I)
  4. Attach the filter housing with carbon block (C,B,A) by twist locking it into place (vertically)

Filter Change

  1. Turn OFF faucet, switch selector to “Tap” position., Twist off filter to remove it from the selector.
  2. Twist open the housing to expose carbon block, discard old filter and replace with new one.
  3. Replace the housing back on to the filter base.
  4. Twist lock the filter housing back onto the selector.
  5. Flush the filter for 60 seconds until water runs clear.

Troubleshooting

  • Q: Water Leaking from the faucet adaptor to threads on mounting nut
    A: Check to see the washer is seated correctly.
  • Q: Slow Flow rate in filter position
    A: Filter Requires Replacement, OR Check Water Pressure OR Check Water Quality
  • Q: Water slow in both “Tap” & “Pure” Position
    A: Clean the Internal Mesh in the Selector – There may be a sediment build up or Calcium.
  • Q: Taste or Odour Issue in filter
    A: If filter is new, allow longer flushing time. If filter is older – Replace Filter.

Size:                120 x 86 x 110 (mm)

Use:                 Municipal (Chlorinated)

Temp:              5°C – 38°C

Pressure:         100 kPa – 400 kPa

Material:          Coconut Carbon Block

Flow Rate:       3L/Min @ 200 kPa

Life:                 3 – 4 Months

                        Harsh Water May reduce filter life

Due to the nature of the products we sell, a strict return policy is in place. We work with food grade certified materials that must be un-opened and un-used as to be able to be re-sold.

You will receive a credit of equal amount, less the postage cost to send it to you. 

  • Wrongly purchased items may be returned for a merchandise credit, this applies for but not limited to: Wrong size, wrong system etc.
  • 30 Day return Policy: We will accept returns up to 30 days after the initial purchase, all orders should be checked immediately for damage/fault upon arrival to aid us with the return process.
  • Return shipping is to be paid by the buyer to the address provided
  • Should the item appear faulty or doesn’t work how described, the unit/item must be returned for testing (if requested), the return postage paid by the buyer. If the unit/item is deemed to be faulty, compensation will be provided for the postage cost. If the unit/item is deemed to be in working order and as described, the buyer will need to pay for return postage. 

If you have any questions about our return policy, please contact us before purchase. This will also help to ensure you purchase the correct product that suits your requirements.

More Information
Product Type N/A
apex-logo
jg-logo
pentak-logo
Haycarb-logo
omnipure-logo
uvg-logo
pure-lite-logo
Hydrasil-logo
Blue-logo
Molytec-logo
FSA-de-min-logo
THERMAX-logo