FREE SHIPPING AUSTRALIA WIDE
Free shipping on all retail orders
AUSTRALIAN OWNED & OPERATED
Licenced WaterMark Supplier
Commercial Stainless-Steel Bag Filter System #1 304SSS | 15m³/Hr* HPF-SS-1
- Commercial Electroplated 304 Stainless-Steel Bag Filter
- EDPM Seals for High Resistance to Chemicals, Oils and High Temperature
- 2" BSP Ports - Suitable for Plumbing use in Australia
- Adjustable Leg Height to suit different applications
- Relief Valve with Working Inlet Pressure Gauge
- Mounting Strainer with 1/8" Holes - Suits Standard #1 Bags
- Eye Bolt for Lid Fastening
Commercial Bag Filter System
This bag filter system is compatible with most standard size #1 filter bags. Supplied standard with 2" BSPT-F ports for easy commercial applications without the need for NPT to BSP adaptors. The inlet and outlet are configured with the inlet on the top side and the outlet at the base of the filter, marked accordingly.
The full-body construction of this system including the internal basket element is made from commercial-grade, acid washed, electro-polished 304 Stainless-Steel making it suitable for domestic and commercial applications including drinking water.
The top seal is a heavy-duty EPDM Gasket for increased resistance to chemicals and oils and has a higher temperature resistance. This seal is used with a heavy-duty screw clamp for a positive seal.
The HPF-SS-1 is considered a high pressure bag filter suitable for applications not exceeding 1600 kPa (225 psi). It is also suitable for domestic or commercial hot water/liquid filtration up to 80°C
For applications over 38°C please contact us to get the correct Nylon or Polyester Filter Bag.
Kit Contains
- Commercial 304SS Bag Filter Housing
- Mounting Legs x3 (Pre-fitted with a ring clamp for adjustment)
- Internal SS Filter Basket with 1/8" Holes for high flow rate
Installation
As per Australian Plumbing Standards, this unit must be installed by a Qualified Plumber in accordance to the manufacturer’s instructions and requirements. Failure to follow these guidelines may void warranty and insurance.
Mounting The System
This filter housing will require a vertical installation on a solid flat surface.
If installing this system on a flat slab, ensure that the slab is at least 100 x 100 (cm) for structural stability. Locate the correct mounting position and adjust leg height by loosening the bolts clamping the legs to the system. When in the desired position, re-tighten the bolts firmly.
Plumbing The System
As with all filtration, it is always recommended to install a bypass around the filter and add isolation valves before and after the system for easy maintenance. Not only will this simplify filter changes, but it will also allow you to maintain unfiltered water flow should there be an issue with the unit, or if the filter is not required at that time.
Ensure that there is a 1-way check valve installed to prevent vacuum on the housing. Excessive vacuum may damage the housing or components.
Using Filter Bags
The stainless-steel bag filter system has an internal SS 304 basket for housing the filter bag. This basket provides structural support for the filter bag to avoid perforation or tearing, resulting in a bypass. The filter bag should be unfolded and placed into the basket, with the rim of the filter bag touching the lip of the basket.
When under water pressure and flow, the filter bag will be forced into the basket and the bag will inflate to provide maximum surface area for filtration. The pressure and flow will seal the filter bag against the rim and prevent raw water bypass.
Filter bags are designed to be cleaned and re-used until their structural integrity has been compromised or the filter material has been saturated.
Working Specifications
Max Pressure: 16 BAR (225 psi)
Temperature: 1°C - 80°C
Max Flow: 15m³/Hr (250L/Min)* Dependent on Bag Selection & Water Quality
In/Out Ports: 2" BSPT-F
Vent Port: 1/4" BSP-F
Drain Port: 1/2" BSP-F
System Dimensions
See Attachment
Return Policy
Due to the nature of the products we sell, a strict return policy is in place. We work with food grade certified materials that must be un-opened and un-used as to be able to be re-sold.
You may receive a refund or credit of equal amount, less the restocking fee if applicable and any other deductions that are relevant.
- Wrongly purchased items may be returned for a merchandise credit, this applies for but not limited to: Wrong size, wrong system etc.
- 30 Day return Policy: Returns will not be accepted without prior approval or after 30 days of invoice date.
- All returns will incur a 17.5% restocking fee or cost to send the item to you whichever greater. FSA may use discretion to determine the restocking fee.
- Any damages (minor, that can be repaired) will incur a fee which will be deducted from the total refund which will be equal to the cost of the replacement
parts (List Price) and labour charge (if applicable) to repair the system(s). This will be separate to the restocking fee. - Any damage considered to be major and not feasible for repair may be refused and the return request will be void. The customer will be responsible for the return freight or disposal of the damaged unit.
- Return shipping is to be paid by the buyer to the address provided. It is recommended that the customer applies transit warranty to the return freight in case of damage.
- Any damages to the system that were not reported to FSA within 48 business hours of receipted delivery are not covered under our transit warranty.
- Should the item appear faulty or doesn’t work how described, the unit/item must be returned for testing (if requested), the return postage paid by the buyer. If the unit/item is deemed to be faulty, compensation will be provided for the postage cost (Proof of cost required). If the unit/item is deemed to be in working order and as described, the buyer will responsible for return postage.
If you have any questions about our return policy, please contact us before purchase. This will also help to ensure you purchase the correct product that suits your requirements.