FREE SHIPPING AUSTRALIA WIDE
Free shipping on all retail orders
AUSTRALIAN OWNED & OPERATED
Licenced WaterMark Supplier
WaterMark Ultraviolet Water Sterilisation System 50L/m Whole House UV 316 Stainless Steel (GT7-8K)
Please note that the GT7-8K UV System has been discontinued.
To buy replacement parts for this system, please see the links below.
***Please note that there are two styles for the GT7-8K System per the below image.***
Type A: Domed Style GT7-8K System - Replacement Parts Below
- 1x 7-8K UV Lamp (Replace Every 12 Months)
- 1x 7-8K Thimble (Replace Every 1-2 Years)
- 1x 7-8NSF O-Ring (Replace Every 1-2 Years (along with Thimble))
- 1x 7-8K Power Source (Ballast)
Type B: Twin Nut Style GT7-8K System - Replacement Parts Below
- 1x 7-8K UV Lamp (Replace Every 12 Months)
- 1x 7-8K Thimble (Replace Every 1-2 Years)
- 2x 7-8NSF O-Rings (Replace Every 1-2 Years (along with Thimble))
- 1x 7-8K Power Source (Ballast)
The GT7-8K has now been superseded by the NEW Watermark Ultraviolet Water Sterilisation System 50l/M Whole House Uv 316 Stainless Steel (7-9K) System.
Full Australian WaterMark Certification
This Water Filtration System is certified to WaterMark Standards AS/NZS 3497 under Certificate Number 23247. WaterMark is the standard that is required by law for a qualified plumber in Australia to install any item on municipal town water. All products used under this certification will give you peace of mind knowing that your water filter complies with Australian plumbing codes. Our WaterMark filtration systems are hand assembled here in Australia and are batch tested to ensure quality and workmanship for your filtration products.
Ultraviolet Sanitation
UV Water Sanitation is by far the most important filtration process when it comes to rainwater treatment. Rainwater harbours bacteria of all types but in some cases, much more harmful bacteria may be present in the tank. E-Coli is a common bacterium in tank water and is due mostly to Frogs in and around your tanks/catchment. Ultraviolet sanitation works by breaking down the cell wall of a micro-organism allowing oxidation to occur which in turn prevents the bacteria from multiplying until it is finally eradicated. Ultraviolet filtration is a chemical-free solution to water sanitation creating no by-products in the water.
We recommend adding the optional UV Thermal Relief Valve for any situation where the UV system is installed and water is not continuously running through the system. This will prevent the UV system from overheating and damaging the seals
Kit Contains
- GT7-8K WaterMark Whole House UV System 40W | 1” Ports
- GT7-8-BRK (x2) 1 Pair of Aluminium Mounting Clamps + Screws
- GT7-8K-Lamp 840mm 4 Pin 40W UV Lamp
- GT7-8K-Thimble 895mm Quartz Thimble 24.5mm*OD
- GT7-8K-PS UL Certified Ballast 40W Australian Plug + Earth Cable
- GT7-8NSF-OR NSF/ANSI 42 Compliant O-Rings Suit 24.5mm*OD
Features
- Commercial Grade Electropolished 316 Stainless Steel Chamber
- Visual & Audible Lamp Failure Alarm
- 1” BSP Threaded Male Connections
- Strong Aluminium Mounting Brackets – Surrounds Chamber
- High Intensity UV Lamps – Up to 50L/min @ 30mJ/cm²
Water Pre-Treatment Specifications
- Hardness < 120 mg/L
- Turbidity < 1.0 NTU
- Iron < 0.3 mg/L
- Manganese < 0.05 mg/L
- Tannins < 0.1 mg/L
- Filtration < 5uM Particulate Filtration
UV System Maintenence Notes:
Ultraviolet systems are rated based on a dosage level of UV-C radiation into the water (mJ/cm²), with 30mJ/cm² being the standard level of disinfection and a minimum dose of 40mJ/cm² required to comply with Australian Drinking Water Guidelines. Our lamps are rated with a 9000 hour (1 year) lifespan, after which point the lamp will naturally degrade and the level of radiation produced by the lamp cannot be guaranteed.
The UV lamp sits inside a quartz thimble, which protects the electrical components of the lamp from making contact with the water. We specifically use quartz (fused silica) for this application because it is strong, exhibits thermal resistance, and has excellent UV transmission properties.
However, over time, metal ions fused within the silica structure of the quartz thimble interfere with the UV-C radiation produced by the lamp, which reduces the UV transparency of the glass and causes it to become fragile. This process is called solarization.
Tannin, bio-film, algae, and scale can also build up on the outside of the glass thimble, further preventing ultraviolet light produced by the lamp from penetrating through the thimble, and impairing the system's ability to sanitize the water passing through.
Thus, we recommend replacing the lamp every 12 months, and the thimble every 1-2 years.
Product Type | Water Filters |
---|
Specifications
Max Flow 50L/Min (For 30mJ/cm² EOL)
Voltage 230-240V
Chamber 316 SS
Ports Size 1” BSP
Max Pressure 125 psi
Working Pressure Up To 70psi
UV Lamp GT7-8K-Lamp
Lamp Power 40W
Lamp Length 840mm
Thimble Length 895mm
Thimble OD 24.5mm
Thimble GT7-8K-Thimble
Ballast GT7-8K-PS
Dimensions
Length 900mm (Without Plug)
Between Ports 780mm
Earthing: Before operating this unit, it must be earthed. Simply attach the supplied earthing cable connected to the chamber to an earthing rod.
Technical Data
UV systems are not designed to be turned on and off. Doing this may shorten your lamp life. Lamps should be changed every year. The lamp may still be working, but after 1 year, the power may not be able to kill all bacteria. The Quartz thimble should be replaced every 2 years. If hardness is high it is recommended to service and clean the UV thimble every 6 months or as required to remove and scale that may build up.
Dosage – GT7-8K
General Disinfection (Common) 30mJ/cm²
Flow Rate Maximum (EOL) 50L/min
Recommended for Drinking Water 40mJ/cm²
Flow Rate Maximum (EOL) 37L/min
UV System Maintenence Notes:
Ultraviolet systems are rated based on a dosage level of UV-C radiation into the water (mJ/cm²), with 30mJ/cm² being the standard level of disinfection and a minimum dose of 40mJ/cm² required to comply with Australian Drinking Water Guidelines. Our lamps are rated with a 9000 hour (1 year) lifespan, after which point the lamp will naturally degrade and the level of radiation produced by the lamp cannot be guaranteed.
The UV lamp sits inside a quartz thimble, which protects the electrical components of the lamp from making contact with the water. We specifically use quartz (fused silica) for this application because it is strong, exhibits thermal resistance, and has excellent UV transmission properties.
However, over time, metal ions fused within the silica structure of the quartz thimble interfere with the UV-C radiation produced by the lamp, which reduces the UV transparency of the glass and causes it to become fragile. This process is called solarization.
Tannin, bio-film, algae, and scale can also build up on the outside of the glass thimble, further preventing ultraviolet light produced by the lamp from penetrating through the thimble, and impairing the system's ability to sanitize the water passing through.
Thus, we recommend replacing the lamp every 12 months, and the thimble every 1-2 years.
Return Policy
Due to the nature of the products we sell, a strict return policy is in place. We work with food grade certified materials that must be un-opened and un-used as to be able to be re-sold.
You may receive a refund or credit of equal amount, less the restocking fee if applicable and any other deductions that are relevant.
- Wrongly purchased items may be returned for a merchandise credit, this applies for but not limited to: Wrong size, wrong system etc.
- 30 Day return Policy: Returns will not be accepted without prior approval or after 30 days of invoice date.
- All returns will incur a 17.5% restocking fee or cost to send the item to you whichever greater. FSA may use discretion to determine the restocking fee.
- Any damages (minor, that can be repaired) will incur a fee which will be deducted from the total refund which will be equal to the cost of the replacement
parts (List Price) and labour charge (if applicable) to repair the system(s). This will be separate to the restocking fee. - Any damage considered to be major and not feasible for repair may be refused and the return request will be void. The customer will be responsible for the return freight or disposal of the damaged unit.
- Return shipping is to be paid by the buyer to the address provided. It is recommended that the customer applies transit warranty to the return freight in case of damage.
- Any damages to the system that were not reported to FSA within 48 business hours of receipted delivery are not covered under our transit warranty.
- Should the item appear faulty or doesn’t work how described, the unit/item must be returned for testing (if requested), the return postage paid by the buyer. If the unit/item is deemed to be faulty, compensation will be provided for the postage cost (Proof of cost required). If the unit/item is deemed to be in working order and as described, the buyer will responsible for return postage.
If you have any questions about our return policy, please contact us before purchase. This will also help to ensure you purchase the correct product that suits your requirements.